Congrats to Tony!

Discussion about anything

Congrats to Tony!

Postby RSbeast » Thu May 28, 2009 8:59 am

For the only person I know to at least have a successful dyno session this year :thumbsup:

I shall return to my garage in disgust :horse:
It whistles while it WORKS.

I suck.
RSbeast
Pro
 
Posts: 1058
Joined: Wed Dec 05, 2007 2:22 pm

Re: Congrats to Tony!

Postby 92tegGP » Thu May 28, 2009 9:23 am

uh-oh...
Image
92tegGP
Modifer
 
Posts: 904
Joined: Sat Dec 29, 2007 1:20 am
Location: North Jackson

Re: Congrats to Tony!

Postby RSbeast » Thu May 28, 2009 9:44 am

...I'm halfway there idk.

After having the secondary fuel pump take dump on me; then came the ignition gremlins.

MSD coils = JUNK btw

Had two setbacks last year, and it got the best of me. Had the ebrake bracket tear down and trash my aluminum driveshaft....making it out of balance. Also had the harmonic balancer separate on me. I can't remeber which happened first.

Well I hadn't got around to changing the driveshaft. Figured I'd do it 1st thing after a tune. Well the harmonics decided to junk my rear main seal on the dyno....covering my clutch in oil.

Ever try making a pull with a fubared clutch? Doesn't work. Even out of boost, my #s were 100rwhp/tq off base (from my (n/a #s) and coming on WAY late. As soon as they started to get everything cleaned up, the oil leaks started and my power started going bye-bye. I went from making 385/390 only taking it to 4k on 4psi rich as fuck with no timing to like 350ish/370-380 at 6k and 11psi with good timing and a/f's. Which are dynojet #s, whereas my car previously on an MD did 296/315 or around 320 dynojet rwhp. It literally feels like a turd of a 30hp gain only felt barely towards redline as I watch the blue smoke from my covered exhaust.

Needless to say I was a a tad disheartened. $3500 should not yeild 30hp and a slug from where it was anyhow down low.
So anyhow, I'm fixing all my leaks and tossing a new clutch back in it and seeing how it does. There's no reason it shouldn't wail past 400rwhp as told by Terry at Street Lethal (GREAT dude to work with btw :thumbsup: :thumbsup: ).

Anyhow I guess I've got some work to do before I give up and build something different. I would add my usual 'fuck mustangs' line....but I think I've already outused it. Sure hope the clutch thing cures it.....cause it sure sucks.

:wrench:
It whistles while it WORKS.

I suck.
RSbeast
Pro
 
Posts: 1058
Joined: Wed Dec 05, 2007 2:22 pm

Re: Congrats to Tony!

Postby Rb25Cory » Thu May 28, 2009 11:07 am

So to do list:

Pull trans
Balance Driveshaft/get new one
New clutch disk
New rear main seal
Reinstall
Return to dyno
Make some numbers

At least your engine is still together.
Function > Form.
User avatar
Rb25Cory
Rice Destroyer
 
Posts: 3306
Joined: Mon Dec 03, 2007 9:24 pm
Location: Youngstown Ohio

Re: Congrats to Tony!

Postby RSbeast » Thu May 28, 2009 12:35 pm

Pretty much.....engine is good 'for now' :|
It whistles while it WORKS.

I suck.
RSbeast
Pro
 
Posts: 1058
Joined: Wed Dec 05, 2007 2:22 pm

Re: Congrats to Tony!

Postby 92tegGP » Thu May 28, 2009 12:53 pm

At least you still have the laser to have fun in
Image
92tegGP
Modifer
 
Posts: 904
Joined: Sat Dec 29, 2007 1:20 am
Location: North Jackson

Re: Congrats to Tony!

Postby Running925 » Thu May 28, 2009 1:16 pm

ohhhh mannnn

i'm really sorry to hear this tom.. thread title had me goin for a sec.. like wtf did i accomplish that i didn't know about! lol


Anyways, best of luck with that thing. It's definatly gonna be a crazy fun car when it's cured of the local curse. My engine will be back in the car in a couple days.
Tony Simeone
100+ hp.. Per Cylinder
CromePro Tuner
http://YoungstownRacing.com
Running925
Modifer
 
Posts: 940
Joined: Mon Mar 10, 2008 2:04 pm
Location: Girard

Re: Congrats to Tony!

Postby g3ar5hift3r » Fri May 29, 2009 2:22 am

RSbeast wrote:...I'm halfway there idk.

After having the secondary fuel pump take dump on me; then came the ignition gremlins.

MSD coils = JUNK btw

Had two setbacks last year, and it got the best of me. Had the ebrake bracket tear down and trash my aluminum driveshaft....making it out of balance. Also had the harmonic balancer separate on me. I can't remeber which happened first.

Well I hadn't got around to changing the driveshaft. Figured I'd do it 1st thing after a tune. Well the harmonics decided to junk my rear main seal on the dyno....covering my clutch in oil.

Ever try making a pull with a fubared clutch? Doesn't work. Even out of boost, my #s were 100rwhp/tq off base (from my (n/a #s) and coming on WAY late. As soon as they started to get everything cleaned up, the oil leaks started and my power started going bye-bye. I went from making 385/390 only taking it to 4k on 4psi rich as fuck with no timing to like 350ish/370-380 at 6k and 11psi with good timing and a/f's. Which are dynojet #s, whereas my car previously on an MD did 296/315 or around 320 dynojet rwhp. It literally feels like a turd of a 30hp gain only felt barely towards redline as I watch the blue smoke from my covered exhaust.

Needless to say I was a a tad disheartened. $3500 should not yeild 30hp and a slug from where it was anyhow down low.
So anyhow, I'm fixing all my leaks and tossing a new clutch back in it and seeing how it does. There's no reason it shouldn't wail past 400rwhp as told by Terry at Street Lethal (GREAT dude to work with btw :thumbsup: :thumbsup: ).

Anyhow I guess I've got some work to do before I give up and build something different. I would add my usual 'fuck mustangs' line....but I think I've already outused it. Sure hope the clutch thing cures it.....cause it sure sucks.

:wrench:


this makes me sad. lemie know if u need any help :thumbsup:

btw, u running the blaster2 coil?
Image
Back on the road again!
User avatar
g3ar5hift3r
Pro
 
Posts: 1361
Joined: Mon Dec 03, 2007 1:16 am
Location: Youngstown, OH

Re: Congrats to Tony!

Postby acvmotorsports » Fri May 29, 2009 8:27 am

Good luck with getting things worked out with this beast!
acvmotorsports
Modifer
 
Posts: 550
Joined: Wed Dec 05, 2007 6:15 pm
Location: Canfield, OH

Re: Congrats to Tony!

Postby craracer05 » Fri May 29, 2009 10:59 pm

Thats sucks really bad tom you'll get it figured out though,and i have to get you thouse jack stands back this weekend.
94 Talon TSi AWD..many mods to come.
Reccomended shops....
Slowboy Racing
JNZ Tuning
craracer05
Fan Boy
 
Posts: 145
Joined: Fri Feb 29, 2008 9:22 am
Location: Youngstown

Re: Congrats to Tony!

Postby RSbeast » Sat May 30, 2009 2:28 am

Brian,

I'll have to check if it was the blaser2 or not. It's the standard TFI coil type, the one that has the black base/red coil; not the new 'all red' coil they sell now.

Stock coil ftw appearently
It whistles while it WORKS.

I suck.
RSbeast
Pro
 
Posts: 1058
Joined: Wed Dec 05, 2007 2:22 pm

Re: Congrats to Tony!

Postby g3ar5hift3r » Sat May 30, 2009 2:05 pm

RSbeast wrote:Brian,

I'll have to check if it was the blaser2 or not. It's the standard TFI coil type, the one that has the black base/red coil; not the new 'all red' coil they sell now.

Stock coil ftw appearently


yeah the blaster2 coil has the black top red coil and mostly blackish sticker, that coil = pos

if ur gonna go msd get the blaster3 coil, or just get something else
Image
Back on the road again!
User avatar
g3ar5hift3r
Pro
 
Posts: 1361
Joined: Mon Dec 03, 2007 1:16 am
Location: Youngstown, OH

Re: Congrats to Tony!

Postby RSbeast » Mon Jun 01, 2009 9:05 am

Well, it's all back together for the most part after I decided to change the oil pan while I was at it......HORRID job with the engine in the car btw.

Just need to change my VC gaskets while I have the upper off, bolt these subframes on while the exhaust is hanging and slip the old driveshaft back in. :thumbsup:
It whistles while it WORKS.

I suck.
RSbeast
Pro
 
Posts: 1058
Joined: Wed Dec 05, 2007 2:22 pm

Re: Congrats to Tony!

Postby Running925 » Mon Jun 01, 2009 10:11 am

yay's

hurry up, track day sunday
Tony Simeone
100+ hp.. Per Cylinder
CromePro Tuner
http://YoungstownRacing.com
Running925
Modifer
 
Posts: 940
Joined: Mon Mar 10, 2008 2:04 pm
Location: Girard

Re: Congrats to Tony!

Postby RSbeast » Mon Jun 01, 2009 1:33 pm

Out of town for work starting thursday and when i get back, im goin on vacation....I get back Super Nats weekend; I just hope to God I have the clutch half broke in by then for when I get dissappointed 2yrs in a row.
It whistles while it WORKS.

I suck.
RSbeast
Pro
 
Posts: 1058
Joined: Wed Dec 05, 2007 2:22 pm

Re: Congrats to Tony!

Postby Running925 » Mon Jun 01, 2009 3:29 pm

RSbeast wrote:Out of town for work starting thursday and when i get back, im goin on vacation....I get back Super Nats weekend; I just hope to God I have the clutch half broke in by then for when I get dissappointed 2yrs in a row.



hopfully mine is still alive when supernats shows up.

I might beat the crap out of this thing on sunday.
Tony Simeone
100+ hp.. Per Cylinder
CromePro Tuner
http://YoungstownRacing.com
Running925
Modifer
 
Posts: 940
Joined: Mon Mar 10, 2008 2:04 pm
Location: Girard

Re: Congrats to Tony!

Postby g3ar5hift3r » Tue Jun 02, 2009 2:02 pm

RSbeast wrote:Out of town for work starting thursday and when i get back, im goin on vacation....I get back Super Nats weekend; I just hope to God I have the clutch half broke in by then for when I get dissappointed 2yrs in a row.


ill break the clutch in for u tom, toss me the keys before u go on vacation ;)
Image
Back on the road again!
User avatar
g3ar5hift3r
Pro
 
Posts: 1361
Joined: Mon Dec 03, 2007 1:16 am
Location: Youngstown, OH


Return to General

Who is online

Users browsing this forum: No registered users and 1 guest

cron