Take back the keys!

i have a 1992 Honda civic hatch.NO rust, clean title. engine is currently out of the car. has eibach springs tokiko struts. no carpet. has carbon fiber hood that's a little beat up. lexan rear windows. can get stock glass if wanted as well. was going to be a race car but decided to move on to something different . as for the engine i have a obd1 b16a. with trans. fresh rebuild not even totally together. SRP 9.5:1 pistons. for turbo set up. eagle H beam rods, ACl race bearings, arp head studs, type R oil pump new water pump, timing belt and tensioner. oil pan tapped for turbo oil return, engine is built for a turbo setup. also has stock b16 trans, no clutch, has p28 ecu. pre chipped with a base map to run the car NA. i have a skunk2 intake manifold that i might throw in for the right price. looking to get $3000 330-248-3172 nick

[EDIT]
forgot to mention.
has Megan racing lower control arms
all bushings replaced with energy suspension poly kit.
both front wheel bearings brand new
new steering rack
msd ignition no cap tho someone broke it.
carbon fiber duckbill
have some spare parts as well
i think thats all... i think...

mmm green looks like a clean car if I had the cash for another project I would take it, good price

thanks man. i wish you had funds as well ha ha. i dont really want to sell it. but i feel that i need to move on.

ehh.. spring is comming and i think i've got enough on my plate.. gonna have to pass on this one.. plus the price isn't exactly a smokin deal.

good choice in most of the parts tho.

how is it not a deal? there is not a spot of rust on the shell. there is well over a grand in engine parts, suspension not the best i know but its not cheap. good trans. good head. i dont see where 3g is not a deal lol.

as for any one else... listing is getting updated for got a few things!

godeaten wrote:how is it not a deal? there is not a spot of rust on the shell. there is well over a grand in engine parts, suspension not the best i know but its not cheap. good trans. good head. i dont see where 3g is not a deal lol.

as for any one else... listing is getting updated for got a few things!

not saying it's a bad deal, just that it's not any kinda steel.. but there are issues here..

you listted that you have a built motor up here but show no spec.'s as far as clearances used on mains / rods / pistons to wall / ring gap / torque spec's used / ect. So that doesn't sound promising and the motor would probably need tore down and re-assembled if not machined until i would trust it.

in the photo it looks to be sitting low as hell.. that poses the question as to how many time's it's been scraped things & how the under side looks.. that would have to be checked into physicaly.

no rust, does that mean that there was rust and it was repaired in the past, or that it never had any?

my comment wasn't meant to put you down in anyway, just to point out that there are bits of information that are questionable in my mind and that i've seen better deals come along. What you have sitting there definatly has a lot of potential and i didn't mean to take that away from it.

Best of luck on the sale.

all clearances are stock checked with a mic and feeler gauges. all torque specs are from honda and arp where applicable. the car has NEVER had any rust. there are a few small dings. underside is clean car has been in the garage since i got it. the engine was torn down only because i thought i spun a bearing but turns out that i had 3 flywheel bolts that were loose.. makes a similar noise apparently. and i figured since the engine was out i would just build it. cylinders were honed as well. i had only driven the car for about 3 months. when the flywheel came loose. the price is OBO too. and i need it gone!

^ you have a pee mmm

mtkhalid wrote:^ you have a pee mmm

never received it!

hmm i send again ! check now !

mtkhalid wrote:hmm i send again ! check now !

yesss.. buy one without electrical issues!!

less computers on fire for everyone!

hahaha im sorry but after Gasper tried his.... i couldn't help but laugh cuz mine was fine. lol AND this GUY needs to check his PM DAMMIT !!!!

do it mo! doooo eeeeeet

i am doing Eeeeeet the best i can. he jsut needs to get online more often ?

i responded.. why do you just want the bottom end? buy the whole thing!

i finally got your pm wooooot !

If I would buy the car can you throw in the camel banner.

if it were my banner it would be a deal.. its from around 1979 from mid ohio. my buddys dad got it when he won one of the series.

Its ok but is that turbo for sale ?

no its sold sorry

Thats ok do you have the b16 head and also how much would you sell the intake mani for ?

i have the entire engine. im tring to sell as a whole. i would ell the mani for about 10 bux less than i paid. still have the box and everything. never been bolted onto anything. but if i dont get what i want and sell the engine its going on my other engine.

price drop to $2100 without intake mani. some one buy this.. i need it gone got kicked out of my house and no longer have a garage to keep it in. and i need the money real bad.

ehh if the price comes down to 1500... lemme know.

i might be interested then. till then

Best of luck to ya.

throw a d16 in there and make it a good dd ill buy it haha